Why Does Bumper Beam Get Removed To Install Draw-Tite Trailer Hitch On 2019 Jaguar F-Pace
Question:
Do i have to remove the bumper beam when I install a hitch on the 2019 Jaguar f-pace. I am looking at the draw-tite hitch 76026
asked by: Larry T
Expert Reply:
The bumper beam is removed and not re-installed when installing the Draw-Tite trailer hitch part # 76026 on the 2019 Jaguar F-Pace because the hitch cross tube is longer so it does not allow the bumper beam to fit back onto the vehicle. The hitch replaces the bumper beam on the vehicle.
I recommend the Curt Trailer Hitch Receiver part # C13291 for the Jaguar because it is a rounder and shorter design that allows the bumper beam to fit around the hitch. I have attached an installation video for your reference.
If you need wiring, I recommend Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118785 for a 4-Way connection at the rear of the Jaguar. The Tekonsha brand wiring has proven to be more reliable and durable than the other brands especially the converters.
If you plan on doing some towing you may consider the etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If you are not sure how much rise/drop you may need in a ball mount to tow your trailer level, I recommend to take a look at the helpful article I have attached about how to figure the amount of rise or drop you may need.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 900 lbs TW
- 6000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Q&A: Replacement Hub/Drum for Triton Axle 08353
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-545-2-G-2K Review
- Video: etrailer Trailer Idler Hub Assembly Review and Installation
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles - 24-5/8" Long
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Q&A: Replacement Bearing Kit and Bearing Buddy Grease Caps for 2012 Triton LT Trailer with Reliable Axle
- Q&A: Should Leaf Spring Capacity Match Trailer Weight or Axle Weight for Best Ride Comfort
- Shop: 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles - 24-5/8" Long
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Video: Review of Dexter Axle Trailer Leaf Spring Suspension - 007-126-01
- Q&A: How Close to Trailer Weight Should Capacity of Trailer Leaf Spring Be
- Q&A: Is Leaf Spring Capacity Rating for One Side or Two
- Q&A: How to Find the Correct Bearings for a Triton LTWCI Trailer
- Shop: 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles - 24-5/8" Long
- Shop: Replacement Trailer Hub Bearing - L44649
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Trailer Wiring
- Shop: Roof Rack
- Shop: Brake Controller
- Shop: Suspension Enhancement