Will the Draw-Tite # 36416 Fit on a 2011 Toyota Camry SE with Dual Exhaust
Question:
I have a 2011 Toyota Camry SE with dual exhaust. I would like to purchase a receiver hitch for this car preferrably one that doesnt bolt to underside of spare tire compartment. Which one would you recommend for my car as far as easy of installation and quality?
asked by: Terry
Expert Reply:
The Draw-Tite Trailer Hitch, # 36416, will fit on a 2011Toyota Camry with dual exhaust. Take a look at the photo I added for you. You can see that the design of the hitch leaves enough room for the exhaust on both sides of the vehicle. I have also linked instructions and a video for you.
At this time there is not a hitch available for the 2011 Toyota Camry SE that does not require bolting to the underside of the spare tire well.
If you plan on doing some towing the correct ball mount is # 36071 and you can use pin and clip # PC2. For a ball use # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter. For trailer wiring, use # 118482.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- Draw-Tite
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class II
- 300 lbs TW
- 3500 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: 1-1/4" to 2" Hitch Adapter For Bike Rack On A 2011 Toyota Camry With The Draw-Tite 36416 Hitch
- Q&A: Recommended Hitch For A 2011 Toyota Camry LE V6 With Dual Exhaust
- Q&A: Will a 1Up Quickrack Trailer Hitch Mount Bike Rack Fit Draw-Tite Trailer Hitch # 36416
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Correct Replacement 1,200 lb Spring Bars for the Blue Ox 2-Point WDS
- Q&A: Difference In Factory Lifestyle Hitch And Frame Mounted Hitch 2021 Kia Seltos
- Q&A: Replacement Boat Trailer Hubs for #82655
- Q&A: Removal of Black Plastic Covering on Underside of 2011 Toyota Camry to Install Hitch
- Article: Flat Towing Package for 2014-2018 Jeep Grand Cherokee
- Article: How to Measure for Trailer Hitch Drop
- Article: What Do I Need To Tow A Trailer?
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Trailer Tire Sizing