Easy to Install Brake Controller Recommendation for 2019 Toyota Tundra

Question

Question:

I have a 2019 Toyota Tundra that has the factory 7 pin connector at the rear of it and i need a brake controller. I would prefer something really easy to install as I hate wiring. Is there something out there that's easy to install and won't require me drilling into the dash panel of my new truck??

asked by: Joel

0

Expert Reply:

We have just what you are looking for with the Curt Echo Mobile Brake Controller part # C51180. This will plug into the 7-way you have at the rear of your 2019 Toyota Tundra and once synced to your smartphone will be ready to go without requiring any hardwiring or splicing. This also allows you to not have to drill into your lower dash too. The controller is proportional too which means it senses how hard you are applying the brakes and will apply the trailer brakes with an equal intensity for a smooth and safe stop.

I attached a review video for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Curt Echo Trailer Brake Controller #C51180 won't itself provide any charge to your trailer mounted battery, but you certainly can still have a 12V power wire ran from the 7-Way to the battery for this purpose with the Echo in place. The Echo…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Easy to Install Brake Controller Recommendation for 2019 Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching