Replacement Wire Cooking Rack For Hisense Microwave

Question

Question:

I lost the rectangle wire rack from my Hisense Over-The-range microwave i bought from you can i replace it

asked by: Nancy

0

Expert Reply:

Yes, the replacement rectangular wire cooking rack for the Hisense Over-the-Range Convection Microwave part # 324-000100 is part # 324-000152.

expert reply by: Heather A

0

Answer 1

I took a look at your High Pointe Convection Microwave Oven Model EC942K9E in your 2019 Fleetwood Discovery 38F, and while I wasn't able to find the specs of the wire rack, I was able to find the dimensions of the cooking chamber. Your High…

view full answer...

Answer 2

I can see why this might be confusing but the information on page 19 that you're seeing is in regards to cookware that did not come with the Furrion Over-the-Range Convection Microwave #FMCM15SS. The wire shelf is designed to be used during…

view full answer...

Answer 3

The Round Cooking Rack #324-000151 has a height of 2-9/16" and a diameter of 11-15/16". Check to make sure that'll work with your microwave and if so, you're good to go!

view full answer...

Answer 4

While I wasn't able to find the dimensions for the rack that fits your Hi Pointe EC942K9E in your 2016 Keystone Montana 3610RL, I do have the dimensions that you can use to determine if the rack will fit. The Replacement Square Cooking Rack…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Wire Cooking Rack For Hisense Microwave

Products Referenced in This Question

Continue Researching