Ramp Option For Trailer With 4 Tapered Bumper For Garden Tractor

Question

Question:

I would like a set of ramps that I can load my garden tractor onto. I’m not sure you have anything that can fit over the bumper on the back of the trailer. I am attaching a photo so you can see what the problem is. Obviously the ramp cannot sit on the bumper so the fingers would have to be extra long

asked by: Donald S

0

Expert Reply:

I do have an option for you but all of the ramps like part # 288-07432 that we carry will not attach the tapered wide bumper that you have in your photo. I recommend to use ramp ends part # 288-07400 on the rubber bumper then you can use 2" x 8' boards as your ramp. These ramp ends measures 5" long and 1" deep.

expert reply by: Heather A

0

click to enlarge

Answer 1

What year is your Ford Fusion and does it already have a trailer hitch? With this information I can make some recommendations for you.

view full answer...

Answer 2

The Aluminum Ramp Ends for 2 x 8 Boards #288-07400 doesn't have anything special that holds the ramps to a tailgate and instead relies on the length and width of the plate, as well as the downward pressure applied by the weight of what you're…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

We have ramps that will work perfectly for loading your 1690lb UTV into the bed of your truck. I recommend the Arched Loading Ramp Set #288-07432-2 which is 90" long x 18" wide and has a combined weight capacity of 3000lbs. The included…

view full answer...

Answer 6

The longest folding ramps we have for you is the Arched Loading Ramp Set part #288-07432 for 1 or part #288-07432-2 for 2 which are 90" long. The 90" length will ensure the angle that will be required to load the generator in your truck bed…

view full answer...

Answer 7

The Stallion #288-07432-2 folding cargo ramps are manufactured in China. If you'd prefer a US made alternative, I'd recommend the Gen-Y #325-GH-R84 84 inch long aluminum loading ramps. If you click the provided link, you can see a product…

view full answer...

Answer 8

I have a solution for you, but unfortunately the Arched Loading Ramp #288-07432-2 set have a maximum safe height of 35", so they would not work for your 37" tall truck bed. You may want to try the Erickson Arched, Aluminum Loading Ramp Set…

view full answer...

Answer 9

I reached out to the manufacturer, Taylor Made, who was able to tell me the stroke length of the Taylor Made Marine Gas Strut for Boat Hatches #3691871-60. They told me the stroke length of this gas strut was 15-3/6 inches. I have added a link below…

view full answer...

Answer 10

The Erickson Horizontal E-Track, part #E19148 has 1/4 inch diameter mounting holes spaced 2 inches apart. The screws you use should be at least long enough to go 3/4 inch into the wood you are mounting the track to. The more screws you use the more…

view full answer...

Answer 11

What will help prevent the bottoming out is a ramp set that is longer and has a bit of an upward bow like the #288-07489 has. Without knowing the length of your current ramps I can't say if these would be an improvement in that area. These are 65…

view full answer...

Ramp Option For Trailer With 4 Tapered Bumper For Garden Tractor

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching