Height of Springs in Timbren Front Suspension Enhancement System # TGMFK15CA

Question

Question:

I was wondering if you could tell me how tall the rubber spring is in this kit?

asked by: Mark

1

Helpful Expert Reply:

Of course!

I went out to our warehouse to take a look at the Timbren Front Suspension Enhancement System Kit # TGMFK15CA and measured a height of right at 2-1/2". I have attached an image to assist.

This particular kit is confirmed to fit your 2014 Chevy Silverado 1500 as long as it's the 4WD model.

expert reply by: Chris R

1

click to enlarge

Answer 1

Yes we do, I attached a picture that shows the installation instructions for the Timbren Front Suspension Enhancement System #TGMFK15CA that you referenced.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

Yes, our Dexter leaf spring part #DX74XR is the same as the part number 072-079-00. This is a 7-leaf spring for an 8,000 lb trailer axle that is 24-7/8 inches.

view full answer...

Answer 10

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 11

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 12

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...

Height of Springs in Timbren Front Suspension Enhancement System # TGMFK15CA

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching