How To Install Break Away For Brake Buddy Braking System

Question

Question:

I need to install the break away switch, do you have a video for that? How to install the brake buddy classic break away switch

asked by: Jim W

0

Expert Reply:

The Replacement Breakaway System for Brake Buddy Classic and Select Supplemental Braking Systems part # HM39340 replaces the brake away switch for the brake buddy Classic II, Select II, Classic 3 (# HM39494), and Select 3 (# HM39524). We have not yet installed the breakaway switch from this setup yet to have a video to for assistance but I have attached the installation instructions for installing the break-away with the Brake Buddy system.

expert reply by: Heather A

0

click to enlarge

Answer 1

A complete flat towing setup consists of base plates, a tow bar, safety cables, tow bar wiring, supplemental braking and potentially a high/low adapter, and I can help you find all of those parts and get you on the road with your 2021 Jeep Grand…

view full answer...

Answer 2

If your 2021 Jeep grand Cherokee has 4WD with a 2-speed transfer case then you can flat tow it with all four wheels on the ground. To do so you'll need a tow bar, base plate, tow bar wiring kit, braking system, and safety cables. I have the…

view full answer...

Answer 3

The Replacement Breakaway System #HM39340 is the correct part for your Brake Buddy 2.

view full answer...

Answer 4

I was able to go out to our warehouse to measure the 3 trailer hitches available that are confirmed to fit your 2018 Jeep JL Wrangler Unlimited. On each of them, I measured from the front mounting plate where it will attach to the back of your…

view full answer...

Answer 5

The correct covers for 1-1/2" openings are the Roadmaster EZ Base Plate 1-1/2" Receiver Covers - Qty 2 Item #RM-210.

view full answer...

Answer 6

We can't recommend you drill into the base plate to mount the breakaway switch as that would void the warranty of the base plate kit. Instead I would recommend mounting the switch to the bumper of the vehicle.

view full answer...

Answer 7

For your 2021 Jeep Grand Cherokee the Roadmaster Direct Connect base plate kit part #RM-521440-5 is a fit and a great option that is easy to use and install. I attached an install video for more info on this kit as well. In addition to the base…

view full answer...

Answer 8

Your assumptions about the braking system on the 2011 Ford Edge are correct. An active braking system, also called a continuous power assist system, is different than what is on your vehicle. You can use the Even Brake #RM-9400 with the 2011 Ford…

view full answer...

Answer 9

A vehicle end wiring harness using a 4-Way Flat connector should have 3 female plugs and 1 male pin. A matching 4-Way Flat trailer connector would have 3 male pins and 1 female plug like on the Mighty Cord Adapter 4-Way Flat to 6-Way Round, part…

view full answer...

Answer 10

I checked with Blue Ox and for your 2021 Jeep Grand Cherokee L model they have the part #BLU47XR as a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat…

view full answer...

Answer 11

Yes, the arms of the Roadmaster Falcon 2 Tow Bar #RM-520 will extend and lock into position when you start pulling your vehicle. The bars can often be difficult to release when you go to disconnect the tow bars from the towed vehicle when you get to…

view full answer...

Answer 12

It can be difficult to remove the front bumper fascia on any given vehicle and the 2019 Jeep Cherokee is no exception. If you take a look at the attached video on the Roadmaster Direct-Connect Base Plate Kit part #RM-521451-5 you will see that if you…

view full answer...

How To Install Break Away For Brake Buddy Braking System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching