Distance from Hitch Pin Hole and Bumper for Curt # 13575 Installed on 2009 Mazda CX-9
Question:
Before purchasing this hitch I wanted to know the distance from the hitch pin to the bumper on the CX-9. I think the Draw-Tite lists the distance as 7 inches, but there is not a distance listed for the Curt. Thanks for your help!
asked by: Thomas H
Expert Reply:
As you can see by clicking on the provided video link, when we installed the Curt # 13575 on the 2010 CX-9 we found that the hitch pin hole to bumper dimension is 4-3/4 inches. The 2009 model should be similar.
In addition to the hitch, you might also need the following to complete your towing system:
Trailer Wiring Harness with 4-Pole Connector # 118520
Ball Mount # D-4
1-7/8 Inch Trailer Ball # 19260
2 Inch Trailer Ball # 19247
Hitch Pin and Clip item # PC3.
I will link you to install instructions and some install videos that you might find helpful.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Bike Rack For Aventon Aventure Fat Tire e Bikes
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Is Lowering the Spare Tire Needed to Install Curt Hitch on 2014 Mazda CX-9
- Q&A: Brake Controller Plug Location for 2020 Chevy Silverado 1500
- Q&A: Easy to Install Trailer Brake Controller Recommendation for 2020 Chevy Suburban
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Replacement Bunk Brackets for Escort Boat Trailer
- Q&A: Recommended Bearing Protectors To Replace Vault Pressurized Bearing Protectors
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Determining Trailer Tongue Weight
- Article: How to Install a Trailer Hitch