Will the Curt Hitch 13344 Fit a 2003 Oldsmobile Silhouette and What Hardware Is Needed
Question:
Will the curt 13344 hitch mount on a 2003 silhouette GLS? If so, is there a hardware kit available?
asked by: Michael
Helpful Expert Reply:
Yes, the Curt Trailer Hitch Receiver part # 13344 is a confirmed fit for your 2003 Oldsmobile Silhouette. The Curt Trailer Hitch Receiver actually comes with all of the fasteners needed for installation so nothing needs to be purchased separately. If you are missing these fasteners then you can obtain them with the Replacement Hardware Kit for Trailer Hitches part # RHK.
If you will be towing a trailer with your Oldsmobile Silhouette you will also need a trailer wiring harness, the Curt Vehicle Wiring Harness part # C55355 and a ball mount/hitch ball, the Ball Mount Kit part # 989900. I have attached install videos on the above parts for you as well.
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Replacement Hardware Kit for Trailer Hitches
- Accessories and Parts
- Trailer Hitch
- Hardware
- etrailer
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: My Trailer Hitch Doesn't Fit
- Q&A: How Does Hitch Install on Chevy Uplander with Load Leveling Compressor
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Closest Metric Replacement Tire Size for 7.00-15 Tire on Livestock Trailer
- Q&A: What Size Thread Tap Would be Needed for Hitch Install Weld Nuts of 2008 Chevy Equinox
- Q&A: Troubleshooting Hitch Install Bolts Not Threading Into Frame Rail Weld Nut
- Q&A: Will the Draw-Tite Trailer Hitch Receiver # 75278 Fit a 2008 Chevrolet Uplander LS MiniShort
- Q&A: How To Determine If 2009 Pontiac Montana SV6 Has Long Or Short Wheel Base
- Q&A: Draw-Tite Trailer Hitch for 2008 Chevy Uplander with 113-Inch Wheelbase
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Hitch Installation Tips
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation on a Ford Full-Size Van
- Article: 5 Things to Know About Weight Distribution Hitches