What Size Lug Nuts Fit Trailer Hub Assembly, Part # 8-213-5UC1

Question

Question:

I am interested if these hubs come with lug nuts and what thread do the studs use?

asked by: Jay P

0

Expert Reply:

The lug nuts, grease cap, bearings, races and grease seals are included with the # 8-213-5UC1 hub you mentioned.

The wheel studs are 1/2 inch diameter, 20 threads per inch.

expert reply by: Mike L

0

Answer 1

When fitting wheels to a Dexter Trailer Hub Assembly, #8-213-5UC1, you would need to measure the wheels you are trying to use. You would measure the bolt pattern, the center hole diameter, and the stud size. To measure the bolt circle on a 6 lug…

view full answer...

Answer 2

The grease used on The Dexter Trailer Idler Hub Assembly #34822545BX, is The LubriMatic Wheel Bearing Grease for Disc and Drum Brake Applications - 14-oz Cartridge #L11465. This grease resists high temperatures, and has a drop point of 520 degrees F.…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

What Size Lug Nuts Fit Trailer Hub Assembly, Part # 8-213-5UC1

Product Page this Question was Asked From

Continue Researching