Diameter of Erickson # EM07706 Truck Bed Ladder Rack Uprights

Question

Question:

I intend to fabricate new mounting brackets to accommodate a Softopper, so I’m hoping to find out the diameter of the upright tubing. Thanks!

asked by: Edward H

1

Helpful Expert Reply:

According to the nice folks at Erickson Manufacturing, the steel tubing that the ladder rack uprights are constructed of measures 1.9 inches (48mm) in diameter. I've provided a photo showing some other dimensions you might find helpful.

I've also linked you to a product description video which you can see by clicking the provided link.

expert reply by: Mike L

1

click to enlarge

Answer 1

The crossbar dimension for the Erickson Truck Bed Ladder Rack, part #EM07706 measures 1.8 inches diameter.

view full answer...

Answer 2

When installed in your 2015 GMC Sierra 2500 the uprights on the Erickson ladder rack #EM07706 will be approximately 57 inches apart, about the same with as the inside width of the bed. When placed side by side the kayaks will be 52 inches wide so it…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

Yes, you can replace your GE air conditoner with an Advent air conditioner like the Advent Air RV Air Conditioner #ACM150. Additionally, you will also need a thermostat. For that, you can use the Air Distribution Box w/ Built-In Thermostat for Advent…

view full answer...

Answer 6

If by serial number you mean VIN and the trailer manufacturer is still in business then yes, you would likely be able to obtain the bearing numbers from the manufacturer. If none of the above are true, then the only other way to determine which…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 10

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Answer 11

For your Atwood water heater number gc6aa-10e, it sounds like you have either a wiring issue or an element issue. To determine if a replacement is needed you will want to make sure the connections are good to and from your switch. I recommend using a…

view full answer...

Answer 12

Yes, the Thule TracRac SR Sliding Truck Bed Ladder Rack #TH57RV will fit your 2020 Ram 1500 with the 5'7" bed and no Ram box. Unfortunately, this rack is only available in the silver color. We do offer the TruXedo Elevate Truck Bed Rack…

view full answer...

Diameter of Erickson # EM07706 Truck Bed Ladder Rack Uprights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching