Wiring Diagram for Trailer Wiring 6-Way

Question

Question:

The wiring was pulled out was wondering which points do the black white and green wires go to.

asked by: Randy

0

Expert Reply:

Assuming your 6-way was wired up using industry standard trailer wire colors you should use the chart I attached that shows how to wire up the 6-way. Use the orientation of the screw on the center pin to know which direction is "up" and down on the diagram.

expert reply by: Jameson C

0

click to enlarge

Answer 1

EB would stand for electric brake on a trailer connector. This is the circuit that carries voltage to the brake assemblies of the trailer. XL would be auxiliary and is typically a 12 volt power circuit used for lights or maintenance charge on a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Hey Michael, thanks for reaching out! The Timbren Active Off-Road Bumpstops #T28GR you installed on your 2018 Ford F-150 unfortunately have that reputation among users (although Timbren claims their systems provide a smooth ride). Because of this we…

view full answer...

Answer 7

I spoke with my B&W representative who confirms that to install their GNRK1121 #BW77FR Turnover Ball hitch on a 2021 Ford F-150, the center of the 4 inch hole for the gooseneck ball would be placed 42-5/8 inches forward of the rear edge of the…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

I went ahead and checked with Curt and and the Curt Double Lock, Flip and Store Underbed Gooseneck Hitch #C60722 is the correct fit for a gooseneck on your 2001 Ford F-150. Having said that, your truck does need to have the holes in the side rails,…

view full answer...

Answer 10

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...

Answer 11

The 2" receiver for the EcoHitch item #EH87SR sticks out right through the middle of the air dam. I have attached a picture below that will show you what this front hitch looks like once installed. The EcoHitch Hidden Front Mount Trailer Hitch…

view full answer...

Answer 12

Yes, the Replacement Cover #PE48UV will indeed fit the 2018 Ford F-150 extended cab with the 67" bed. This is made to be a replacement cover for the Pace Edwards JackRabbit Retractable Hard Tonneau Cover #311-JRFA05A28 which is specifically for…

view full answer...

Wiring Diagram for Trailer Wiring 6-Way

Product Page this Question was Asked From

Continue Researching