Possible Replacement Landing Gear Jack Gear Box to Fit 2006 Open Road Pilgram

Question

Question:

I have an 2006 open road by pilgram 37ft 5th wheel i had no power to the trailer and was tying to rise the landing lags by manually cranking from the outside and the pin gave out well this work?

asked by: Leo M

0

Expert Reply:

If the gear box you have on your 2006 Open Road looks just like the part # LC276602 it would be the correct replacement as this is a very common gear box replacement. If you have something that looks different email me a picture of it and I'll see if we can get you what you need.

expert reply by: Jameson C

0

Answer 1

Yes, the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies #LC276602 is a great replacement product for most 5th wheel factory landing gear as it works with Atwood, Lippert, and Stromberg-Carlson landing gear.…

view full answer...

Answer 2

The Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies #LC276602 you were looking at fits the vast majority of landing gear assemblies those made by Atwood, Lippert, and Stromberg-Carlson. With that said the only…

view full answer...

Answer 3

I went out to the warehouse to measure replacement gear box #LC276602. From the base of the gear box to the end of the shaft on the output side it is 4.75 inches. From the end of the shaft to the center of the pin is 1.35 inches. The diameter of…

view full answer...

Answer 4

Yes, based on the picture you sent in the replacement gearbox part #LC276602 that you referenced is the correct replacement. This is aluminum too which means it will be a bit stronger as well.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 8

For the gearbox on your 2008 Forrest River Sandpiper I recommend the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies #LC276602. The aluminum casing is far more sturdy than the plastic housing options. If you…

view full answer...

Answer 9

For your Venture landing gear you can use #LC276602 or #LG-179015. Either one will work.

view full answer...

Answer 10

It could be the motor but it could also be the screw/nut inside the jack leg that is causing the problem. Since you mentioned that it is hard to crank it manually I suspect that it is likely the screw and/or nut. On jacks that have an ACME screw the…

view full answer...

Answer 11

We have just what you need to replace your landing gear motor M9000PK with the #LC196308 and you'd be set! This is a confirmed fit for what you have and is a faster motor too so your jacks will raise and lower quicker.

view full answer...

Answer 12

Yes, the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies #LC276602 is the correct replacement gear box for your VMC40RB-091565 gear box.

view full answer...

Possible Replacement Landing Gear Jack Gear Box to Fit 2006 Open Road Pilgram

Product Page this Question was Asked From

Continue Researching