What is Trailer Weight Capacity of of Equal-i-zer Shank # EQ90-02-4800

Question

Question:

I dont see a tow weight rating on this. I only see a tongue weight rating. What is the tow weight rating on this shank?

asked by: Geno

0

Expert Reply:

The total trailer weight capacity of the Equal-i-zer weight distribution shank part # EQ90-02-4800 is 16,000 lbs.

I attached a picture that shows this capacity stamped in the side of the shank.

expert reply by: Jameson C

0

click to enlarge

Answer 1

No, it does not. The hitch ball does not come mounted on the Equal-i-zer Weight Distribution item #EQ37101ET. You will need to use a 1-7/8" Thin walled socket like item #EQ70-00-4800 to get it installed.

view full answer...

Answer 2

Best option for you is going to be to get the optimum weight distribution setup for when you are loaded to the max and then when not loaded either use less spring bar tension or not use the system at all. Reason being when you need the system the…

view full answer...

Answer 3

The hitch you'd use will depend on the outside to outside distance apart your frame members are. If this distance is between 18-51 inches, use #C13701. For a span between 22-66 inches, use #C13704. Both hitches have a tongue weight capacity of…

view full answer...

Answer 4

The MORryde X-Factor Crossmember #MR99ZR is designed for LRE, RE, or TRE Leaf Spring Suspension systems so since you're using the Dexter E-Z Flex Suspension Kit #K71-653-00 you'll want to use the MORryde X-Factor Dropdown Crossmember #MR84AR…

view full answer...

Answer 5

In regards to choosing the correct weight distribution shank, you really only need to pay attention to the hitch size and rise/drop. The brand won't matter as much as they are all pretty much universal in this regard. The Equal-i-zer Weight Dist…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

What is Trailer Weight Capacity of of Equal-i-zer Shank # EQ90-02-4800

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching