Brake Controller Output Wire on ETBC

Question

Question:

on a 2007 ford escape using the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires Item # ETBC7 -Where is and what color wire is the brake controller switch wire?

asked by: Daniel S

0

Expert Reply:

I am not 100 percent certain what you are asking but the blue wire on the Universal Installation Kit for Trailer Brake Controller # ETBC7 is what will connect to the output wire on the brake controller. I have added two articles for you, one on installation of trailer brake controllers and the other on the ETBC7 kit, and I strongly recommend reading both as they have detailed explanations. If you were instead asking about the stop light switch wire, that would be the wire that only gets power when you press the brake pedal, and the brake controller itself would be attached to that wire.

expert reply by: Kyle S

0

Answer 1

When powering a brake controller like the Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR you have to power it directly from the vehicle battery. Mainly because it would prevent the controller from shorting out any of your vehicle's…

view full answer...

Answer 2

Not to confusing at all. There are a lot of wires to keep straight, but once you do it, you will be surprised at how easy it was. I will go through a quick run down of how to wire up the ETBC7, then how to wire up the Brake Controller. I will also…

view full answer...

Answer 3

There are some wires that run along the frame rail on your 2014 F-150. I have attached a photo that shows where you can find the wires. They will be on the driver side. I have attached a link to a helpful article on installing a brake controller on a…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Good morning, Cliff. As of today (3/27/24) we are expecting the #KE33JR tire/wheel combo to be in stock in about 2 weeks. Hopefully this means we can take our own pictures and put them on the site within maybe about 3-4 weeks from now. What I can…

view full answer...

Answer 9

Hey Roy, The only U-bolt kit we currently only offer for 1-1/2" square axles is part #CE23102, which only has a 3-3/8" length so it likely wouldn't be the best option for you. Instead you'll want to order the 1-1/2" Square…

view full answer...

Answer 10

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

If you remove the hub and wipe away the grease on the spindle you can check to see if it is damaged. Look for an scarring, gouges, discoloration, or scoring on the spindle. If the spindle is damaged then the bearings won't ride properly and can…

view full answer...

Brake Controller Output Wire on ETBC

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching