Correct Load Stops for TracRac Ladder Rack

Question

Question:

does this fit the trac rac ladder rack as well? looks like a much better option than the loops that come with it and break so easily

asked by: Matthew D

0

Expert Reply:

The Replacement Load Stops # 753-3761 are compatible with the TracRac Ladder Racks that were re-branded under Thule. These ladder racks have "XT" at the end of their part number and will have "Thule" somewhere on them (typically the uprights).

expert reply by: Jon G

0

Answer 1

The correct load stops for a TracRac Ladder Rack will be based on which version you have. If you have the Thule branded ladder rack then you will need to use the Thule TracRac Ladder Rack Load Stop part #8537165 with the Washer part #951-0820-20…

view full answer...

Answer 2

While your photos did not come through, I can tell you that for an older TracRac, the load stop you mentioned is indeed the correct part. They are solid individually, and if you also need the knob, washer, and t-bolt, we have those as well. So what…

view full answer...

Answer 3

I have a great solution for you. Unfortunately, while Thule could not verify the channel slide piece of the Replacement Load Stop for Thule Ladder Racks #8537165, my contact at Thule confirmed that the load stop will not be able to fit into the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Correct Load Stops for TracRac Ladder Rack

Product Page this Question was Asked From

Continue Researching