8-248 Dexter Hub Recommendation for a 3,500 lb Axle with a 5 on 4-1/2 in Bolt Pattern

Question

Question:

I am looking for a replacement hub assembly for my 6x10 Continental Cargo enclosed trailer. The hubs on it right now are Dexter and marked with 8-248. I believe its a 3500# axle and the bolt pattern is 5 on 4.5. The axle spindle is an EZ Lube model with the zerk fitting on the end. Is this the correct replacement hub for my trailer? Thanks!

asked by: Bill D

0

Expert Reply:

Yes, the Dexter Hub # 8-248 has the same L68149 inner/ L44649 outer bearings as the Trailer Hub Assembly # 84545UC1-EZ that you referenced so it will work for you.

This hub also has a 5 on 4-1/2 bolt pattern like you need.

expert reply by: Jameson C

0

Answer 1

As long as the seal in the bearing kit part #BK1-150 is flush with the hub it is okay to have a small gap between the seal and inner bearing. When installing the seal you only insert it enough so that it is flush with the hub. The seal's job is…

view full answer...

Answer 2

If you know the trailer axle capacity that's a pretty good way to determine what spindle you have. Or if you get me the bearing numbers. You can also measure the spindle where the bearings ride and with that info I can let you know what you…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 5

Thanks for providing all of the information for your axle. This axle is going to use the standard 3,500 lb axle bearing sizing. You can use the Bearing Kit #BK2-100, which will come with bearings, races, seals, cotter pin and tang washer - everything…

view full answer...

Answer 6

The only option I have for you to store a torsion axle trailer with the wheels off the ground is by using jack stands, the Powerbuilt Unijack Bottle Jack part #ALL620471 would be a good option as they have built-in bottle jacks and offer up to…

view full answer...

Answer 7

The hub you want as a replacement for what you sent in a picture of is the Kodiak Trailer Idler Hub Assembly #Q-HUB84545 which is a galvanized hub for a 3,500 lb axle with a 5 on 4-1/2 inch bolt pattern.

view full answer...

Answer 8

You can use the other components you remove from your hubs. After you have removed the hub components you will want to inspect all of the parts and replace if you find any discoloration or signs of wear or damage such as a nick. On the race you can…

view full answer...

Answer 9

In order to find the correct replacement hubs for your Shoreland'r boat trailer, you need to first know what bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the…

view full answer...

Answer 10

The trailer will have a plate or sticker on it that will list the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that will list the weight capacity. You can…

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 12

Thank you for all of the details! According to the information you sent in you need the Hub Bearing Kit #BK2-100 as well as the Bearing Buddy Stainless Steel Bearing Protectors #BB1980A-SS. The hub bearing kit has everything you need for an…

view full answer...

8-248 Dexter Hub Recommendation for a 3,500 lb Axle with a 5 on 4-1/2 in Bolt Pattern

Product Page this Question was Asked From

Continue Researching