Does SumoSpring Solo Kit for 2016 Ram 3500 Fit Dually and Single Rear Wheel Truck

Question

Question:

Is there a different part number for the dually vs srw ?

asked by: Bob Z

0

Expert Reply:

The SumoSprings Solo part # SSR-312-54 that you referenced fits both the dually and the single rear wheel versions of the 2016 Ram 3500 so it will work great for your dually model.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For suspension enhancement that helps with body roll a lot of people swear by the SumoSprings. Which for your 2015 Ram 2500 the recommended kit is the part #SSR-312-54 which fits 2WD or 4WD. This will fit your truck and work well with your 2,500 lb…

view full answer...

Answer 2

Yes, you can omit the spacer included with the SumoSprings Solo Custom Helper Springs part #SSR-312-54 which will allow the suspension to compress more before the springs engage. If you're looking for a smoother ride you can also switch to a…

view full answer...

Answer 3

For your 2016 Ram 2500 I recommend the SumoSprings Solo Custom Helper Springs - Rear Axle #SSR-312-54. The SumoSprings are a great choice to help with a bouncy ride. These springs minimize sway, cushion bumps and shocks, and also have a minimal…

view full answer...

Answer 4

The SumoSprings Solo Custom Helper Springs part #SSR-312-54 is 6-3/8 inches from the top of the attached mounting bracket to the bottom of the spring where it would sit on the table. I have linked a photo for you to check out showing where Kaitlyn…

view full answer...

Answer 5

For a great set of SumoSprings for your application, that is the rear axle SumoSprings Solo Custom Helper Springs #SSR-312-54. This model provides 2,800 pounds of load leveling capacity for your 1,480 pounds of added vertical tongue weight with your…

view full answer...

Answer 6

I'd go with the lighter duty SumoSprings part #SSR-312-54 if you ever plan to drive the truck without your trailer connected as the ride quality would be much nicer than the higher rated #SSR-301-47-2 that you mentioned.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hi Joe, Yep, you heard correct, you can go from a 2 inch shank to a 2-1/2 inch shank with your Reese weight distribution hitch without issue. One of the following 2-1/2 inch shanks should have the right rise/drop for your application. Here are the…

view full answer...

Does SumoSpring Solo Kit for 2016 Ram 3500 Fit Dually and Single Rear Wheel Truck

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching