Inside Diameter of YR12000 Keel Roller With Plastic End Caps Removed

Question

Question:

I have a 12inch keel roller with 1inch in diameter bar. I was wondering if this would fit if the white spacers can be removed? thanks

asked by: Jack

0

Expert Reply:

It certainly would. According to Bob Yates of Yates Rubber, the inside diameter of the # YR12000 keel roller is a bit under 1-1/4 inches with the white plastic plugs knocked out. This would be the perfect roller for your needs.

expert reply by: Mike L

0

Answer 1

A couple sets of the Dutton-Lainson Boat Trailer Deluxe Roller Bunk - 5' Long Sections - 12 Sets of 3 Rollers #DL21741 will drastically help with getting your pontoon boat on and off the trailer smoothly and easily as there isn't any friction…

view full answer...

Answer 2

We do have some of the replacement rollers that will work for your vintage 1965 boat trailer, but we do not have some of the rollers you asked about. Thank you for the dimensions. For the very front keel roller I recommend part #YR5213-5. This…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 10

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 11

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 12

That is an excellent question and is asked more often than you think. Electric brakes like what come in the Electric Trailer Brake Kit #AKEBRK-2 can be submerged in water when you are loading/unloading your boat. Since water and electricity don't…

view full answer...

Inside Diameter of YR12000 Keel Roller With Plastic End Caps Removed

Product Page this Question was Asked From

Continue Researching