Finding Receiver for Pairing Replacement Lippert LINC Remote

Question

Question:

Were is the receiver that you have to push to link the remote

asked by: Crystal

0

Expert Reply:

The receiver location for the Lippert LINC system that you need to access to pair the Replacement Remote # LC292614 can vary between different trailer/RV models but typically it's somewhere near where the generator is stored. If you can't find the receiver there then your best bet will be to try and contact the trailer/RV manufacturer and they should be able to tell you its whereabouts.

expert reply by: Chris R

0

click to enlarge

Answer 1

There will be 4 wires coming from the Lippert Replacement Electric Jack Switch #LC387874 that you are looking at. The blue wire from the switch will go to a 6 amp breaker like #LC134181 that is installed between the switch and jack motor. This will…

view full answer...

Answer 2

For your Lippert Components Power Stabilizer Trailer Jack #LC298707 the wiring is pretty simple. There are two wires that come out of the motor and they are both used as power or ground depending on the direction you want to turn the motor. To…

view full answer...

Answer 3

The Lippert Components Power Stabilizer Trailer Jack #LC298707 referenced in your question is indeed compatible with the Linc remote. This simply means that the jack can be operated using the Linc Analog Remote #LC292614. You would not need any…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 7

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 8

Your 13-10 equalizers, which should be equivalent to Equalizer #TREQ310 measures 6-1/16 inches from bolt hole to bolt hole (see accompanying photo) and due to that you will need to use the E-Z Flex Heavy Duty Rubber Suspension System #K71-652-00.…

view full answer...

Answer 9

I've actually answered a similar question on this before and found: In my research I found that the grease seal you are looking for could have an inner diameter of either 2.24 or 2.12 inches and an outer diameter of 3.37 inches when measured with…

view full answer...

Answer 10

We don't offer an 8500 lb rated surge coupler, but we might have options that would work for you. If the GVWR (weight of trailer plug boat) is 8000 lbs or less, I'd recommend the Demco item #DM8669113 if your trailer has disc brakes or item…

view full answer...

Answer 11

For a 4-way trailer wiring harness for your 2017 Lexus RX350 that has the tow package you would want the part #56083 which is a confirmed fit. This harness does not have a converter box built into it and it just plugs right into a port you have at…

view full answer...

Answer 12

The LaSalle Bristol XTRM PVC RV Roof Membrane #3441700534142711440 ships rolled up on a tube just like how it's pictured.

view full answer...

Finding Receiver for Pairing Replacement Lippert LINC Remote

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching