Correct 3-Step SolidStep Assembly for 25-1/2 Inch Doorway Width

Question

Question:

my door to my camper is 25 1/2 inches so what size step would I need

asked by: Harol

0

Expert Reply:

I reached out to my contact at Lippert and she said that if your doorway width is 25-1/2 inches the SolidStep Manual Fold-Down Steps # LC791572 will work perfectly. They do have this listed for door widths of 26 inches to 29-7/8 inches as you likely noticed but she said it will fit your 25-1/2 inch width.

This 3-step assembly features leg extensions to create a sturdy platform and a stowable design that keeps them inside the entry door when not in use. I have attached the written installation instructions that you can also check out.

expert reply by: Chris R

0

Answer 1

We've seen this issue before on an older camper that had the screen door installed a little lower than how they are now. An installer here actually had this exact problem. If your door is close to closing, a couple suggestions that you can try…

view full answer...

Answer 2

The SolidStep Manual Fold-Down Steps for 25" to 28-7/8" RV Door Frames - Triple - Aluminum, #LC791572, has adjustable legs that adjust in 1" increments. When drawn fully in the feet can be pulled in approximately 1" from the…

view full answer...

Answer 3

Because of your concerns with your wife's ability to make a larger first step, I suggest you go with the third step option of the SolidStep, #LC791572. This triple step is designed to fit 25" to 28-7/8" wide doorways as measured from…

view full answer...

Answer 4

As you can see by the cut out of the instruction manual for the SolidStep Manual Fold-Down Steps #LC791572 you will need the parts you see in the cut out of the linked installation instructions. If you have a laminate floor you will need #10-4"…

view full answer...

Answer 5

The SolidStep Manual Fold-Down Steps part #LC791572 will fit a door way from 25" -28.9" wide when measuring the frame inside. If the factory label sticker shows a doorway width between 26"-29" then the above steps will work for…

view full answer...

Answer 6

In terms of choosing a Lippert Solid Step, you'll use the width of the finished door at it's narrowest. Round that number up to the next full inch, which in your case would be 28 inches. In that case, you'll want the adjustable model…

view full answer...

Answer 7

Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.

view full answer...

Answer 8

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 9

The MORryde StepAbove RV Steps #MR85RR weighs about 70 lbs. As far as the flip step, I assume you are referring to the MORryde Flip Tread RV Steps #MR42UR which weighs about 45 lbs. Both of these steps will fit your 28" wide door. Personally I…

view full answer...

Answer 10

I recommend Advent Air RV Air Conditioner part #ACM135C for the 8.5x24 ft enclosed trailer. The temperature range is 65 degrees F to 90 degrees F so it will keep your enclosed trailer nice and cool on hot days. You can also add a heat strip with part…

view full answer...

Correct 3-Step SolidStep Assembly for 25-1/2 Inch Doorway Width

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching