Can Noise with Friction Sway Bar be Used

Question

Question:

Is there anything you can do about the noise? it sounds like you drive over a whale when you make any turn. especially sharper turns.

asked by: MV

0

Expert Reply:

Sway control bars, like the Curt # 17200, battle trailer sway using friction as the bar slides in and out. It has pads that the bar slides against creating the friction to fight sway. Unfortunately, creating friction in the manner is far from quiet but it's necessary to do its job. Anything you do to reduce the noise, such as lubricating the arm that rubs against the friction pads, will not only reduce the noise but also reduce the effectiveness of the entire unit.

expert reply by: Charles S

0

Answer 1

Since the Tuson Electronic Sway Control System #335TSC-1000 will activate either side of the trailer brakes as needed to stop sway and the Curt True Course #C94VV instead applies them both at the same time and does a better job sensing and stopping…

view full answer...

Answer 2

Yes, you can use the Reese Friction Sway control part #83660 without a weight distribution system. You would just need to use the tab part #RP26003 on the ball mount as well.

view full answer...

Answer 3

The Curt Friction Sway Control, #17200, can be used without a weight distribution system like you mentioned by using the Reese Sway-Control Bracket you referenced, #RP26003. This system helps to fight trailer sway, but only after it begins by adding…

view full answer...

Answer 4

Your understanding of how the air in the bags will operate is correct. If both bags are on one valve the air will shift from one to the other while turning with a heavy load. However, if the load is distributed evenly it will also return to even once…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 11

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 12

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...