Outer Diameter of Bearing # TJA-2000-BR

Question

Question:

I need O.D. of bearing # TJA-2000-BR

asked by: Keith K

0

Expert Reply:

The outer diameter of the bearing # TJA-2000-BR that you referenced is 1.025 inch.

expert reply by: Jameson C

0

Answer 1

The Replacement Bearing for etrailer and Ram Round, Sidewind Jacks - 2,000 lbs and 5,000 lbs, #TJA-2000S-BR, has an outside diameter of 1.22 inches. The inside diameter of the bearing is 1/2 of an inch. The width of the bearing measured almost 15/32…

view full answer...

Answer 2

I went out to our warehouse for you to double check, the Replacement Bearing for etrailer and Ram Round, Topwind Jacks part #TJA-2000-BR has an I.D. of .50" and an O.D. of 1.025".

view full answer...

Answer 3

The Replacement Bearing for etrailer and Ram Round, Topwind Jacks #TJA-2000-BR has an inner diameter of 0.5", an outer diameter of 1.025", and a thickness of .477". When you go to install this bearing, you'll want to put the thrust…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Outer Diameter of Bearing # TJA-2000-BR

Product Page this Question was Asked From

Continue Researching