How To Support the Slide-Out On a 2019 Grand Design Transcend 28MKS

Question

Question:

Can I use this support for the slide

asked by: Bert

1

Helpful Expert Reply:

We have just what you are looking for. These supports will signifcantly reduce bounce and movement for slide outs. Ultra-Fab has two sizes of slide out supports - sold in quantities of 2 per package.

The Ultra-Fab # UF19-960003 supports can be adjusted from 26" to 47" and are rated for 1400 pounds each.

The Ultra-Fab # UF19-960001 supports can be adjusted from 16" to 28" and are rated to support 1400 pounds each.

These supports keep your camper in tip-top shape. Extendable struts work in tandem to keep your slide out level and to prevent sagging and damage to your RV's extension tubes. Quick-release handles make mounting a snap.

We recommend a support for each gear track under the slide out. I placed a link to a demonstration video below.

expert reply by: Conner L

1

Answer 1

The only way to get a new control panel would be to replace your entire Smart Jack with part #LC643589. I reached out to my contact at Lippert who confirmed that the only replacement parts for the jack includes hardware like the pin or the footplate.…

view full answer...

Answer 2

I have a complete replacement jack option for you, but the buttons on your Lippert Smart Jack #LC643589 are not replaceable so the only option is a complete replacement. If your jack is still within the 1-year warranty period then I recommend…

view full answer...

Answer 3

I checked and found the manual for the Lippert Electric Trailer Jack #LC285318 and there was no mention of anything going in the hole beforehand to tighten them. I added a cut out of the manual for you which shows the parts for this jack, and it does…

view full answer...

Answer 4

You can change your cam locks to slam latch locks but it will take modifying your hatch doors. You can use the Global Link RV Baggage Door Slam Latch with Keyed Alike Option - Black - 1-1/2" Thick #295-000015 along with the Global Link Mounting…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

How To Support the Slide-Out On a 2019 Grand Design Transcend 28MKS

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching