Diagnosing, Locating and Repairing Trailer Ground Problem
Question:
tail lights on trailer work fine until I turn on my running lights then they go out
asked by: phil
Expert Reply:
My suspicion is that you have a poor ground connection somewhere on your trailer. The fact that everything works fine until the running lights are turned on is the dead giveaway. When the tail lights are turned on, the trailer lighting is drawing maximum amperage through the system. If there is a ground problem, this is when it will manifest itself.
There are several places to look for a poor ground connection. Lets start with the trailer connector on the vehicle. Trace the white wire coming off of the connector, and make sure it is securely grounded to the vehicle frame or chassis. Check that this connection is securely made to clean metal. Having the ground wire connect to metal that is corroded or covered with excessive undercoating will prevent a proper metal-to-metal connection. Next, move on the the connector on the trailer itself. Follow the ground wire and locate the point where it attaches to the trailer frame, which is usually on the trailer tongue. Make sure this connection is secure and not corroded.
Next, check the individual lamps. Each lamp will pick up its ground connection either through a separate ground wire connected to the trailer frame, or by its mounting bolts being in direct contact with the trailer frame. If a ground wire on each lamp is used, once again make sure its connection is tight and not corroded. If the ground connection is made through the mounting studs, make sure the mounting studs are in direct contact with the trailer frame. If the lamps are mounted to wood or plastic, you might have to run a short jumper wire from the mounting stud to the trailer frame.
A final possibility is the design of the trailer itself. Some utility trailers that feature a tilting bed can have ground problems. The trailer is actually two pieces, the frame being one piece and the bed being the other. Since the lamps are typically attached to the bed, if the bolts that connect the two portions of the trailer together which are used as the pivot point become worn, the two halves of the trailer will not have consistent metal-to-metal contact, thus causing an insufficient ground connection. This problem can fixed by connecting the two portions of the trailer together with a jumper wire.
Locating the problem will involve a process of elimination, but the problem should be found in one of the places I have mentioned.
I have linked you to some troubleshooting videos you might find helpful. To view them, click on the provided links.
Product Page this Question was Asked From
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 4 Flat
- Draw-Tite
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Wiring
- Search Results: winch stand
- Article: Trailer Wiring Diagrams
- Shop: Optronics LED Combination Trailer Tail Lights - Submersible - 40 Diodes - Driver and Passenger Side
- Shop: Fulton Heavy-Duty Winch Strap with Hook - 20' x 2" - 4,000 lbs
- Video: Pollak 10-Terminal Junction Box Installation
- Shop: Trailer Hitch
- Q&A: How to Choose Correct Capacity for Trailer Safety Chains
- Q&A: How to Correct Weak Ground Connection on Vehicle and Trailer
- Shop: CE Smith Winch Stand - Galvanized Steel - 30" Tall x 2" Wide
- Search Results: bow stop
- Search Results: bow stop mounting bracket
- Search Results: winch bracket
- Search Results: winch mounting tray
- Q&A: Does Trailer Lighting Ground Through the Hitch Ball
- Shop: etrailer Tongue Weight Scale for Campers and Utility Trailers - 2,000-lb Capacity
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Q&A: Should There Be Continuity Between Running Lights And Ground Circuit While Bulb Is Disconnected
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Shop: Submersible, Under 80" Trailer Light Kit with 25' Wiring Harness
- Search Results: trailer lights
- Search Results: ground
- Shop: Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger - Top Load
- Video: Hopkins Trailer Breakaway Kit Review
- Video: Pollak Wiring PK52248 Review
- Q&A: Can the Trailer Lighting Ground Through the Hitch Connection
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Hopkins 7-Way RV Style Trailer Connector w/ LED Test Lights Review
- Q&A: Trailer Running Lights Do Not Work but Brake Lights and Turn Signals Do Work
- Shop: Towing Mirrors
on Trailer Wiring
Chris
5/14/2024
Thanks Mike L, for sharing your understanding. Poor grounding is a common source for electrical gremlins, and the dump trailer hinge is a cause I would have overlooked if not for your post. — Greatly appreciated.