What Does UWS A-Frame Trailer Toolbox # UWS01065 Weigh

Question

Question:

How much does this item weigh?

asked by: Chad

0

Expert Reply:

The UWS A-Frame Trailer Toolbox # UWS01065 that you referenced weighs 37 lbs total. Other dimensions of it are 24" long (front) 49" long (rear) x 18" wide x 21" deep.

expert reply by: Jameson C

0

Answer 1

The first thing to check is to make sure that the sensitivity or output settings on your Curt Echo #C51180 did not change from your original settings. It also may be beneficial to re-adjust the controller from scratch. In order to do this, Curt…

view full answer...

Answer 2

Though the UWS A-Frame Trailer Toolbox - 6.3 cu ft - Gloss Black #UWS01065 will measure 49 inches at the back, 24 inches at the front, 18 inches deep, and 21 inches tall, I cannot suggest using it as a propane tank case. This is due to propane tanks…

view full answer...

Answer 3

These toolboxes do not contain mounting hardware due to the different construction and mounting locations that may be required for many different styles of trailers. A lot of how you install the UWS A-Frame Trailer Toolbox #UWS01065 depends on where…

view full answer...

Answer 4

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 5

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Answer 6

So I have your hub narrowed down to a few different possibilities but we need to know what your bolt pattern is to know for sure. We have the part #84556UC3 for if your bolt pattern is 5 on 5 inch. We have the part #845476UC3 for if your bolt pattern…

view full answer...

Answer 7

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 8

Slipper Springs like #e33SR do not use a bolt and bushing for the open eye end of the spring. It connects directly to the hanger using a slipper spring hanger kit.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

There is no mounting hardware included with the Aluminum A-Frame Trailer Tongue Toolbox, item #350970, due to the different construction and mounting locations that may be required for many different styles of trailers. I would recommend using a…

view full answer...

Answer 11

Aluminum A-Frame Trailer Tongue Toolbox Item #350970 is weather resistant but not waterproof. For something to be considered waterproof it has to be able to be submerged under water for a certain period of time and not let water in. None of the…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

What Does UWS A-Frame Trailer Toolbox # UWS01065 Weigh

Product Page this Question was Asked From

Continue Researching