Replacement Step Pads for 3 Inch Nerf Bars

Question

Question:

is there a after market replacement pad that will fit a 3 inch nerf bar

asked by: Sam

0

Expert Reply:

There are many step pad replacements available for nerf bars and each one has a slightly different measurement and mounting pin locations. For instance, I've attached the Replacement Step Pad for Westin E-Series Nerf Bars - 21" Long x 3" Wide - Qty 1 # 23-0001 with a diagram to assist.

I've linked the page to all the options we carry.

expert reply by: Jason S

0

click to enlarge

Answer 1

It sounds like you need the Replacement Step Pad for Westin Platinum Series Oval Nerf Bars - Front/Rear - Qty 1 #21-0001. You can see the measurements in the photo and that there are 6 pegs, but only 5 of them use the clips to hold the pads in place.…

view full answer...

Answer 2

The replacement step pads you need for the Westin Platinum Oval series are #21-0001. You may also want the Replacement Barrel Clip for Westin Platinum Series #23-0002.

view full answer...

Answer 3

The Westin Replacement E-series Step Pad, #23-0001, measures 3-5/8, 5-5/8, 6-3/8, 3-5/8 inches from one end pin to the other. I have attached a photo showing the measurements I took for you. It is 21 inches long and 3 inches wide. This certainly does…

view full answer...

Answer 4

The closest replacement pad we have to what your mentioned is the Replacement Step Pad for Westin Signature Series Nerf Bars - 19-3/4" Long - Qty 1 #26-0001. I have attached 2 photos of one of this replacement pad. One photo shows the outside…

view full answer...

Answer 5

I went out to our warehouse to take a look at the Aries Replacement Step Pad #AA2090139 that your referenced and measured a distance of right at 3-3/4" between the first two pegs, on center. While out there I went ahead and measured the spacing…

view full answer...

Answer 6

The spacing of the pins on the Replacement Step Pad for Aries 3" Wide Oval Nerf Bars #AA2090139 are as follows. The first pin from each end is 3-3/4", to the next pin on one side is 5-1/2" and to the other side is 6-5/16". I have…

view full answer...

Answer 7

While we don't have a direct replacement step pad for your 3 inch round TruckChamp nerf bars, other people have been able to use the Replacement Step Pad for Westin E-Series Nerf Bars #23-0001, you referenced. From my research, your TruckChamp…

view full answer...

Answer 8

We don't currently carry Retrac products and I'm not able to pull up the dimensions for their 3 inch bars so I can't confirm compatibility of the Westin Replacement Step Pad #23-0001 with these steps. With that in mind your best option is…

view full answer...

Answer 9

You can click on the linked page to see all our brands of tube steps for your 2006 Dodge Ram Pickup. You will want to try to visually match your nerf bars to those shown to narrow down the many options to the specific style and brand you have. First,…

view full answer...

Answer 10

We don't carry Truck Champ products, so I couldn't say with any certainty if the #23-0001 replacement step pad you looked at would work for you. I can, however provide the dimensions of the pad and show you a photo with the pin spacing so you…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Replacement Step Pads for 3 Inch Nerf Bars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching