Will Dexter 12 inch Brake Assemblies Fit 2009 Texas Pride Tandem Trailer

Question

Question:

I have a 2009 Texas Pride dual 7000 lb axle 16foot dump trailer, are your 12inch nev-r-adjust, Item 23-464-465 the correct replacement brake components. Texas Pride was not listed in your list of manufactures and models the the brakes fit.

asked by: PHILLIP C

0

Expert Reply:

Most likely yes since the Dexter brake assemblies part number # 23-464-465 are designed to fit standard 7K trailer axles like you'd have but it wouldn't hurt to check first. Take of a hub drum and measure the inside diameter and width. If it's 12 inch by 2 inch and the assembly is held to the brake flange with a 5 bolt pattern then this kit is the correct fit for it.

I also attached a review video for these assemblies and a link to a page on adding brakes to a trailer you might find helpful.

expert reply by: Jameson C

0

Answer 1

Sounds like you are looking for a Bulldog collar lok style of adjustable coupler with a higher capacity which we do offer with the part #BD028657. This actually has a slightly higher weight capacity at 15,000 lbs.

view full answer...

Answer 2

Many times Dexter hubs will fit on a Lippert axle, but Lippert does have a few axles out there with special spindle sizes. Every Lippert axle comes with a tag or plate on the axle that gives a serial number or NV number. If you can give me that…

view full answer...

Answer 3

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 4

There is no specific torque rating when reinstalling the castle nut after packing the bearings. You want to run the nut down until there is no side to side play in the hub, and then back it off to the next notch in the castle nut so the retainer can…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Buddy, so the Fastway Adjustable Ball Mount part #DTSTBM6825-2S is a really great choice for the 2-1/2 inch hitch of your 2021 Ford F-250 which is going to be very solid in your hitch due to it's built in anti-rattle device that is easy to…

view full answer...

Answer 7

Yes, the B and W Companion Slider Hitch part #BWRVK3370 does fit the OEM prep kit of a 2021 Ford F-250 Super Duty. Newer trucks do sit up higher but so do the newer fifth wheel trailers to compensate for that so as long as the truck doesn't have…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

For your application you need the Air Lift LoadLifter 5000 which has that 5,000 lb weight capacity you mentioned. Please note that suspension enhancement is designed to help the OEM suspension on your 2021 Ford F-250 and won't increase the weight…

view full answer...

Answer 11

Each of the leaves on the Leaf Spring #e47SR are 3/8" so this will give the spring pack a height of 1-1/2". Here is a list of our U-Bolt Kits for a 3" axle. Redline #APUBR-9 Dexter #APUBR-8 CE Smith #CE23003

view full answer...