Wrench Size for Tightening Hitch Pin Bolt of Swagman Hitch Pin Lock S64029

Question

Question:

Wrench or Socket Size for Threaded Hitch Pin for swagman xc2

asked by: Boris M

0

Expert Reply:

You'd need a 19 mm socket or wrench to tighten the bolt of the Locking Anti-Rattle, Threaded Hitch Pin for Swagman Hitch Racks # S64029.

expert reply by: Jameson C

0

Answer 1

Thanks for reaching out! I recommend swapping out your Class II Curt Hitch #C12108 for the etrailer Hitch #e98864 for your 2017 Toyota RAV4. This is a Class III hitch with a 2" receiver which will accommodate both your Malone kayak trailer and…

view full answer...

Answer 2

What's likely occurred is that rust has formed in the receiver tube, making the ball mount fit more tightly than it ordinarily would. I'd recommend obtaining a spray lubricant like PB Blaster and flooding the gap between the ball mount and…

view full answer...

Answer 3

The part #S64029 that you referenced takes a 22 mm or 3/4 inch wrench to tighten the bolt side of it. The same size wrench is used for the #S64031. The hitch pin of the Swagman Trailhead part #S63360 is also the same size. The #e98891 can be keyed…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 7

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 8

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

I have a solution for you. Here at Etrailer, we strongly discourage using wheel-mounted bike racks like the Kuat NV 2.0 #NV22B for bikes with fenders. Mounting wheels with fenders can cause the fenders to crack or become damaged, especially with the…

view full answer...

Wrench Size for Tightening Hitch Pin Bolt of Swagman Hitch Pin Lock S64029

Product Page this Question was Asked From

Continue Researching