How To Use Internal Hose Coupler On RV Sewer Hoses

Question

Question:

How to make the coupler fit the 2 hoses, heat? How would we do that?

asked by: Estene

0

Expert Reply:

As long as the RV sewer hoses are 3 inch in diameter without a bayonet fitting like Camco part # CAM39611 the hoses will slide over each end of the coupler part # CAM39203 to join them together. You do not need to heat the coupler up to seal the connection.

expert reply by: Heather A

0

Answer 1

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 2

Sometimes just use of new spring bars can update a weight distribution hitch to match the tongue weight (TW) of a new trailer, but in the case of your Equal-I-zer system, part #EQ37140ET, the highest-rated bars are the 1400-lb set #EQ90-01-1499 that…

view full answer...

Answer 3

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 4

I think the best way to explain how to install a grease seal like #10-9 is to take a look at the video I have linked. Go to about the 6 minute, 10 second mark. At this point in the video, our installer begins to install the seal in the back of the…

view full answer...

Answer 5

I did some checking and basically the cutout bumper is the regular factory bumper. The Curt hitch, #C15312, will fit up tighter and a little more recessed, apparently the same way the factory hitch does if it were installed. Some people like the…

view full answer...

Answer 6

The confusion is that the two answer pages have two different hitches they are referring to. The #C15312 measures 2-3/4 inches from the mounting flange down to the hitch opening and the #C15313 measures 5-5/8 inches. I attached a picture that has…

view full answer...

Answer 7

Yes, I looked up the weight of your 2000 Chevy Silverado 1500 and since the max weight it can be configured as is 4,784 lbs the 5k Blue Ox tow bar part #BX7322 would work. The correct Blue Ox base plate kit to use with this would then be the part…

view full answer...

Answer 8

The B and W trailer hitch #BWHDRH25189 for the 2002 GMC Sierra is indeed rated for use with weight distribution. We are in the process of updating the information but if you look in the specs section of the product page you will see that you can use…

view full answer...

Answer 9

In regards to the B&W Heavy-Duty Trailer Hitch Receiver part #BWHDRH25189, the distance from the flange to the top of the receiver tube is 3-1/8" and the distance from the rearmost mounting hole to the end of the receiver tube is…

view full answer...

Answer 10

When initially setting the power on your Prodigy P3 Brake Controller #90195 you will follow the process you stated. I've attached these instructions to further assist. You will get up to 25 mph and release the gas pedal and then fully engage the…

view full answer...

Answer 11

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Answer 12

The Curt Hitch part #C15302 will fit very tight to your rear bumper. It would be hard for me to venture a guess as to how much higher it would sit than your factory hitch. But I can give you a way for you to figure it out. When installed, the #C15302…

view full answer...

How To Use Internal Hose Coupler On RV Sewer Hoses

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching