Will Camco Vented RV Bumper Cap Fit 3-3/4 by 3-3/4 Inch Inner Dimensions?

Question

Question:

Thanks for the info Jason. My bumper is not standard. I had it custom built to replace my old standard light-weight bumper that had structural damage. My bumper is 1/8" wall thickness, where standard is 1/16" wall. If I order this part on the basis that you say it will fit (tight), and then find it does not fit, can I return it at no cost to me? I'd rather not go through the hassle if there is a good chance it will have to be returned. Thanks

asked by: Joseph W

0

Expert Reply:

The Camco Vented RV Bumper Cap w/ Tether # CAM40324 will fit your standard 4 inch bumper that has inner dimensions for 3-3/4 inches by 3-3/4 inches nice and snug. The integrated fins will keep this cap secure to give you a clean finished look to your bumper and allow you to either store things within or keep things out.

expert reply by: Jason S

0

click to enlarge

Joe

3/29/2019

Thanks for the info Jason. My bumper is not standard. I had it custom built to replace my old standard light-weight bumper that had structural damage. My bumper is 1/8" wall thickness, where standard is 1/16" wall. If I order this part on the basis that you say it will fit (tight), and then find it does not fit, can I return it at no cost to me? I'd rather not go through the hassle if there is a good chance it will have to be returned. Thanks

Reply

Jason S.

3/29/2019

You obviously have a unique situation so I went to the warehouse to make the specific measurements for you so you can be confident about the fit. From outside edge to outside edge it is 4-1/8 inches square. From the farthest fin edge to edge it is 3-7/8 inches. From the smallest point to the smallest point not accounting for the fins it is 3-9/16 inches. The fins are a very sturdy plastic and not very flexible at all. They are designed to fit and grip so there is some give, but they are not flimsy. It is likely you'd need to sand or file the fins if you are planning on taking this cap in and out. If you will be leaving it in, you can most likely use a block and hammer to drive it into place without any modifications. I hope that info is helpful.

Reply

Answer 1

The Camco Olympian 5500 Stainless Steel RV Propane Grill #CAM57305 has a width of 18 inches and depth of 11-1/2 inches. The Camco Camping Griddle - 16-1/2" Long x 10" Wide #CAM51048 will work well for this grill to give you the cooking…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Will Camco Vented RV Bumper Cap Fit 3-3/4 by 3-3/4 Inch Inner Dimensions?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching