How To Prevent Front End Sagging on a 2005 Winnebago Sightseer with Workhorse P32 Chassis

Question

Question:

Currently the RV is sagging on the front end. Very low. What coils woudl I use for a gvw of 18,500 on 2005 workhorse p32 chassis. 2005 Winnebago sightseer. 8.1 liter GM v8. Upgraded weight capacity would also be good.

asked by: Gianny T

0

Expert Reply:

I called SuperSprings about the SuperCoils Custom Suspension Coils for your 2005 Winnebago Sightseer on a Workhorse P32 Chassis and they recommend that you use the SuperCoils Custom Suspension Coils part # SSC-10 which have a 5,700 lb capacity (per coil). This was selected based off of the 18,500 gross vehicle weight rating (GVWR) of your motorhome. They stated the SuperCoils Custom Suspension Coils part # SSC-11 which have a 7,200 lb capacity (per coil) are more suited for commercial applications.

expert reply by: Conner L

0

Answer 1

If you are needing to replace the factory coil springs at the front of your 2004 Workhorse P32 chassis then the higher-rated Super Springs SuperCoils #SSC-11 will work perfectly. These heavy-duty springs will maintain your RV's ride height but…

view full answer...

Answer 2

Unfortunately there currently isn't a steering stabilizer fit available for your 1996 Chevy P30 Chassis. I can completely understand where you're coming from with the poor ride quality in motorhomes having driving numerous models here so I do…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 12

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

How To Prevent Front End Sagging on a 2005 Winnebago Sightseer with Workhorse P32 Chassis

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching