How to Remove Old Butt Connector to Install New Trailer Tail Lights
Question:
I ordered theses trailer lights or a similar model from you, but have a question as to how to remove the old lights before I install the new ones. I have attached two pictures of the light fixtures in question on my horse trailer. As you can see, they are in bad shape and are in need of renewal. I am a novice at this, but I can see that the wire from the trailer is joined to the wire from the lights via a blue connector see attached photos. I cant seem to separate the two wires. Is there a trick to this?
asked by: Emanuel S
Expert Reply:
When a butt connector is used to connect your wiring you will simply need to cut the butt connector off on the trailer side. You should be able to see some metal inside the butt connector that has been crimped down. Try to cut the wiring as close to that as possible so that you don't lose too much of it.
Once the wire is cut just strip some of it back and use new butt connectors for the installation. I recommend using heat shrink butt connectors like part # DW05745-5 as they provide an excellent seal against any corrosion or water that may try to get in.
Product Page this Question was Asked From
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Wiring
- Wire Connectors
- Butt Connectors
- 12-10 Gauge
- Deka
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Video: Fantastic Vent RV Vents and Fans FVK8017-00 Review
- Q&A: Replacement Fan Motor for Fan-Tastic Vents 4000-Series Roof Vent
- Shop: Replacement Fan Motor Assembly Kit for Dometic FanTastic Roof Vent Fans
- Shop: Dometic FanTastic Roof Vent Assembly Upgrade Kit - Clamp-on - Power Lift - 14-1/4"x14-1/4"
- Shop: Peterson Clearance and Side Marker Trailer Light - 2 Bulbs - Oblong - Red Lens
- Video: Review of Deka Wiring - 12-10 Gauge Butt Connectors - DW05745-5
- Q&A: Butt Connectors For 10 Gauge Wire For Electric Trailer Brakes
- Shop: Wire Cutters with In-Handle Crimper and Bolt Cutter - 8" Long
- Shop: Heat Gun - 572 to 932 Degrees - Dual Fan Speed - 12 Amp - 1,500 Watts
- Shop: Performance Tool Crimping Pliers - 10 to 22 AWG Wire - 9-1/2" Long
- Shop: Brake Controller
- Search Results: pm~108~15
- Q&A: Replacement LP Gas Detector
- Q&A: Replacement Atwood RV Propane and Carbon Monoxide Detector
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Brake Controller
- Search Results: trailer brake controller
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: brake controller
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer lights
- Shop: Suspension Enhancement
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Q&A: Parts Needed To Add Electric Drum Brakes To A Pontoon Trailer
on Wiring
