Installation of Replacement Joint Assembly Hardware Kit for Lippert Electric Coach Step

Question

Question:

Just received the Replacement Joint Assembly Hardware Kit for my Kwikee steps. What is the proper order for installing the step bolt? Does the bolt go through from the outside, then slide the bushing on from the inside, with the small end facing the step, then the washer, then the locking nut? Or does the washer go on the outside next to the bolt head? Thanks.

asked by: Graham R

0

Expert Reply:

I reached out to to the manufacturer, Lippert, who told me that to install the Replacement Joint Assembly Hardware Kit for Lippert Electric Coach Step # LC216567 who told me the bushing will go in the hole, and then you put the bolt through; the washer will go on after than, and then the nut.

expert reply by: Kyle S

0

Answer 1

We do have a solution for you, however the shoulder bolts are not available individually. Instead, there is one as a part of the Replacement Joint Assembly Hardware Kit #LC216567. It comes with a 5/16"-18 Diameter x 1-1/4" long hex-head…

view full answer...

Answer 2

You mentioned part number 216657 which I could not find anywhere. I did, however, find Replacement Joint Assembly Hardware Kit for Lippert Electric Coach Step #LC216567. This replaces the hardware in 1 joint assembly on your single, double, or triple…

view full answer...

Answer 3

The only parts list for your triple step is attached. It unfortunately does not give the breakdown to the extent you are seeking with Teflon plate and wave washer as those parts are not replacement options from the manufacturer. I've attached the…

view full answer...

Answer 4

From your description it sounds like you are looking for the Replacement Double Ball Joint #LC388220, although this is the entire ball joint and not just the bolts. This connects the gear plate to the actuating arm on a Lippert Coach Step or…

view full answer...

Answer 5

I reached out to my contact at Lippert about what might be going on with your Never Fail bushings, like what comes with kit #LC281285, and he said that it sounds like you may be using the Never Fail bushings to push out your bronze bushings. If this…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Installation of Replacement Joint Assembly Hardware Kit for Lippert Electric Coach Step

Product Page this Question was Asked From

Continue Researching