Internal Dimensions of TorkLift PowerArmor Locking Battery Box

Question

Question:

What are the interior dimensions of the TLA7708R battery box? Will it hold two size 29 batteries that have a dimension of 13L x 6.75W x 10H?

asked by: H. S

0

Expert Reply:

When we measured the internal dimensions of the TorkLift PowerArmor Locking Battery Box # TLA7708R we found that it was 26-1/2" long x 7-3/8" wide x 12-9/16" high. This means it would work with your pair of 13" long x 6-3/4" wide x 10" high batteries so long as that 13 inches was measured at the longest point of your batteries. If so there would be a half-inch or so to spare.

You can take a look at the linked video review which details these measurements at the end of the video.

expert reply by: Kyle S

0

Answer 1

We do have parts available for the 2024 Toyota Tundra 4WD models so we can definitely set you up. For an air bag kit I recommend the Air Lift #AL84JQ. These are the 5,000 lb capacity air bags. They will help level your ride and improve overall…

view full answer...

Answer 2

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

What I would do is go out to your truck and measure out 71 inches and 65 inches on a tape measure and compare that to the width of your bed. If you think the 71 inch looks better and would suit your needs then that's what you would want to go…

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

Hey Parvez, glad I could help! So the Rhino Rack Vortex Crossbars for Retrax XR tonneau covers part #RRVA180B-RRRLT600 was designed specifically to work with your RetraxOne XR tonneau cover so it is going to definitely have enough clearance above…

view full answer...

Answer 8

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...

Answer 9

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

I'd be happy to recommend a cargo carrier to fit with the Rhino-Rack Vortex Crossbars for Retrax XR and Mountain Top EVO-M Tonneau Covers #RRVA180B-RRRLT600 on your 2022 Ford F-250 Super Duty! I really like the 53" x 49" Yakima OffGrid…

view full answer...

Answer 12

We do have the parts needed for a Thule Wingbar EVO to fit the slots of a Retrax cover but not as a complete kit. Here's what you'd need: 60" WingBar Evo Crossbars - #TH711520 Evo Clamp Feet - #TH710501 Fit Kit - #TH29TX Lock Core Kit -…

view full answer...