End Caps for RV 4 Inch x 4 Inch Square Bumper

Question

Question:

Does this have a square cap to fit it in the square bumper?

asked by: Burt

0

Expert Reply:

The Revolution RV Sewer Hose Kit w/ Swivel Fittings and Storage Caps part # CAM39625 does not come with the end caps for your RV's 4" x 4" square bumper. The end caps that are included are for the hose only. If you need the end caps for your RV's 4" x 4" square bumper then you can obtain them using the Camco Vented RV Bumper Cap w/ Tether part # CAM40324.

expert reply by: Conner L

0

Answer 1

We offer trailer wheel center caps in sizes for a 2.84-inch wheel pilot hole, part #AM90113, all the way up to caps for wheels with a 5.15-inch pilot hole, part #AM90078. In about the middle of this range is the part #319EZ that you referenced, which…

view full answer...

Answer 2

We sure do! The #AM90092 center cap you referenced is the correct center cap for the 16 inch series 06 wheel you mentioned.

view full answer...

Answer 3

We did have one customer come back and say there was some noise with the Demco Recon part #DM8550045 while towing but most have reported back that it worked well for them without noise mentioned at all. I wouldn't say this has a reputation for…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between load ranges varies based on the tire size and brand. When comparing two tires of the same size and brand, a load range D tire will always have a greater weight capacity and psi rating than a load range C. However, when…

view full answer...

Answer 9

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 10

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

End Caps for RV 4 Inch x 4 Inch Square Bumper

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching