Scissor Jack Stabilizer Jack Compatible with 8,000 lbs

Question

Question:

Is there any scissor jack with a LIFT capacity of 8000 lbs?

asked by: Pascal

0

Expert Reply:

Scissor jacks are stabilizing jacks and not intended for lifting. Their rated capacity is only for stabilizing. We have kits with capacities above 8,000 lbs but the largest support capacity for a single jack is the Ultra-Fab Ultra Scissor Jack - 24" Lift - 6,500 lbs # UF48-979006 or the 30 inch lift # UF48-979032.

So if you use one on each side of your trailer that gives you a 13,000 lb support capacity at that location since you wouldn't put it on one side and not the other.

expert reply by: Jason S

0

Answer 1

Provided that you have the space and mount it properly you could mount a scissor jack such as #UF48-979032 any which way you want. You might be interested in a different type of stabilizer such as #UF39-941705 which is electric or #UF39-941704 which…

view full answer...

Answer 2

A replacement stabilizer scissor jack needs to have the mounting pattern to fit your trailer, as well as the lift and needed weight capacity. For example, I have added a photo of the mounting plate of the Ultra-Fab Ultra Scissor Jack #UF48-979032. It…

view full answer...

Answer 3

The individual weight is 10 lbs for one of the stabilizers in the Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4 #TJSCHD-24-4.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Scissor Jack Stabilizer Jack Compatible with 8,000 lbs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching