Could Dexter Trailer Hub part # 8-219-13UC3 Be Used on an EZ Lube Spindle
Question:
Can Dexter Hub # 8-219-13UC3 with 9/16 Studs be used with Ez-Lube Axle if you just put Grease Cap with Rubber Plug when Installed.
asked by: Bobby J
1
Helpful Expert Reply:
Yes, you can swap out the grease cap of the Dexter Hub part # 8-219-13UC3 to one that has a hole and rubber plug and it would be perfectly compatible with EZ Lube spindles. For that all you'd need is the part # RG04-120 and you'd be set. The only difference between the Dexter EZ lube hubs and non EZ lube hubs is the cap.
expert reply by:
Jameson C
1
Products Referenced in This Question
Grease Cap, 2.72" OD Drive In with Plug - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- E-Z Lube Grease Cap
- 2.717 Inch O.D.
- Redline
more information >
Product Page this Question was Asked From
Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Pre-Greased
- Standard
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 9/16 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Continue Researching
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Shop: Brake Controller
- Video: Choosing the Right Brake Controller
- Video: Trailer Brakes and Wiring Installation
- Shop: #42 E-Z Lube Spindle w/ Flange for 5.2K to 7K Trailer Axles - 2-1/4" Diameter
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb E-Z Lube Axles - 12" - 8 on 6-1/2
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 1/2" Studs
- Shop: Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 5/8" Studs
- Q&A: Do Self-Adjusting Trailer Brake Assemblies have to be Initially Adjusted
- Q&A: Suspension Enhancement For a 2021 Grand Design Momentum 353G With 7,000LB Dexter Axles
- Q&A: How to Install Races in a Hub Assembly
- Q&A: How to Adjust Self-Adjusting Trailer Brakes
- Q&A: Troubleshooting Weak Braking After Installing New Dexter Electric Brakes on Trailer
- Q&A: Replacement Hub Recommendation for Hub Stamped 8-219
- Q&A: Troubleshooting Newly Installed Self-Adjusting Brake Not Working Properly
- Search Results: 8~219~13
- Search Results: 7k drums
- Search Results: 42 spindle
- Search Results: 008 219 13
- Video: Bearing Repacking and Grease Seals Installation
- Video: etrailer Trailer Bearings Races Seals Caps - Races - 25520 Review
- Search Results: 25520
- Shop: Replacement Race for 25580 Bearing
- Shop: Trailer Wiring
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: etrailer Electric Trailer Brake Kit Installation
Explore Expert Info
![Our Expert]()
on Trailer Hubs and Drums
on Trailer Hubs and Drums
