Will the Putco Chrome Fender Trim Fit Dual Rear Wheel Fender on a 2018 Ford F-350

Question

Question:

Part number P97285 - Will this fit a 2018 F350 with Dual Rear Wheels?

asked by: Ken D

1

Helpful Expert Reply:

Since the Putco Stainless Steel Chrome Fender Trim # P97285 are a universal fit, I spoke with my contact at Putco who said that they haven't had any problems with customers fitting the trim on duallys so it should fit just fine on your 2018 Ford F-350 with Dual Rear Wheels.

I have attached the photos from the installation instructions for you to check out as well.

expert reply by: Jon G

1

click to enlarge

Answer 1

According to Putco, the #P97285 will fit your 2022 Ford F-350 SuperCab with dual rear wheels.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Will the Putco Chrome Fender Trim Fit Dual Rear Wheel Fender on a 2018 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching