Will Fulton XLT Trailer Jack Bolt to Same Bracket as FXP15W

Question

Question:

I have an ez loader with a fxp15w, and the bracket is welded on. With this xlt 141132 mount to that welded bracket, they look identical....

asked by: Robert F

0

Expert Reply:

Yes, the Fulton XLT Bolt-Thru Swivel Trailer Jack # F141132 that you referenced is designed to fit the same style of mounting bracket that you have in the picture you submitted. This jack will bolt right up.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Fulton jack part #F141132 that you referenced is a really great jack that I know you'll be happy with, but it requires the bracket part #P9012-00 to mount to a trailer which isn't the same as what you have now. So your best option is to…

view full answer...

Answer 2

The Trailer Valet RVR9 Remote-Controlled Trailer Mover #TVRVR9 is a 4-motor device. There are other versions of this unit that use fewer motors but this one has 4. The maximum surface slope compatible with this device is 5 degrees. I did confirm this…

view full answer...

Answer 3

To convert your axle for a top mounted leaf spring I would recommend replacing the U bolts, nuts and tie plates, so your best bet would be to go with a U bolt kit. For a 2-3/8" round axle use #APUBR-1 For a 3" round axle use #APUBR-9 You…

view full answer...

Answer 4

The Fulton F2 Fully Enclosed Trailer Winch #FW20000301 does not have any kind of adapter plate to allow you to mount it to a different bolt pattern. You will have to drill new holes if you want to use this winch. I attached a diagram below with the…

view full answer...

Answer 5

The 'sleeve' or shank portion of the Fulton #F500266 caster assembly is meant to be compatible with Fulton F2 trailer jacks, which is why it's kind of oddly shaped. At the widest point, that sleeve is 2-1/2 inches in diameter, as shown in…

view full answer...

Answer 6

Good question, and what happens is that leaf springs elongate over time, and since you mentioned you got measurements of 25-1/2 inches from center eye to center eye and 26 inches under partial load, the best option for leaf springs really is the…

view full answer...

Answer 7

The only difference between the Blue Ox SwayPro #BXW2000 and #BXW2003 systems is that the 2000 is for a standard trailer while the 2003 is for a trailer with an underslung coupler. So if you have a standard coupler use the kit 2000 but if you have an…

view full answer...

Answer 8

To replace your 12" brakes I recommend checking out the 7K TruRyde Electric Trailer Brake Kit #TRU96FR or the 5.2K - 7K Hydraulic Trailer Brake Kit #AKUBRK-7 depending on what kind of braking system you have. You'll also need the Mounting…

view full answer...

Answer 9

You can definitely install the HappiJac tie-downs in the front and use Torklift tie-downs for the rear, but you'll have to purchase the whole Happijac kit #LC236326-205221 since we don't currently offer the front separately. For the rear…

view full answer...

Answer 10

I do have a handy trailer wiring FAQ article that would be perfect for you. I have included a link to it. I have also included a picture that shows the typical wiring diagram of a 7-Way round pin trailer side connector. As you can see, the 7-way…

view full answer...

Answer 11

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Will Fulton XLT Trailer Jack Bolt to Same Bracket as FXP15W

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching