Trailer Hub w/6 Lug Pattern, Inner Bearing Inner Diameter 1.5, Outer Bearing Inner Diameter 1.25

Question

Question:

Im looking for 6 lug hubs for my trailer it has house trailer type hubs now. But the inner bearing is 1.5inch outer is 1.25inch . All the the hubs that I can find that replace house trailer hubs are 1.75inch inside. This is a two axel gooseneck is factory build . thanks

asked by: Fred H

0

Expert Reply:

Bearing measurements need to be as accurate as possible, to at least the thousandth of an inch, and require calipers if you have to measure them. Otherwise look at the bearing numbers that are stamped into the sides of the bearings. With those numbers we can determine a lot about the running gear and if anything else will fit.

If the measurements are exactly 1-1/2 and 1-1/4 inches then the only option we have would be agricultural hub # AH30660FCOMP which has a 6 on 6 bolt pattern.

If you find the bearing numbers let me know what they are. The hub above uses inner bearing LM29749 and outer bearing LM67048.

expert reply by: Michael H

0

Answer 1

The first thing to try to is add some penetrating oil like WD40 and let it sit for awhile. You can then try tapping the bearing to try and remove it. You don't want to hit it too hard because you can damage the spindle. It is possible that the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 12

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Trailer Hub w/6 Lug Pattern, Inner Bearing Inner Diameter 1.5, Outer Bearing Inner Diameter 1.25

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching