Availability of Optronics Double Bullseye Clearance Light with Black Base

Question

Question:

specifies 10 diodes..... clearly pictures show 8 LEDs. Whats the reality? do these come with BLACK bases?

asked by: Mike

0

Expert Reply:

The Double Bullseye Optronics clearance lights like the # MCL45AB have 8 diodes not 10. For a black base you'd want # MC42AB.

expert reply by: Jameson C

0

Answer 1

The SAE number on a trailer's lens isn't the most reliable way to pick out a replacement lens as that is not the part number for the light. The best solution I can provide would be to have you measure the dimensions of the clearance lights…

view full answer...

Answer 2

Yes we do have a red version of the Optronics Double Bullseye with the part #MCL45RB. The amber version is part #MCL45AB.

view full answer...

Answer 3

We don't offer a replacement lens for a Fruehauf LCE-8750, but we do offer a equivalent lamp from Optronics, part #MCL32RB for the LED version or #MC32RB for the incandescent. We do offer a replacement lens for the incandescent version, which is…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Availability of Optronics Double Bullseye Clearance Light with Black Base

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching