Replacement Lock Cylinder Compatibility with Leer Camper Shell

Question

Question:

I have a Leer 100R camper shell on my Toyota Tacoma. Will these lock cylinders work in the handles on my camper?

asked by: Jon R

0

Expert Reply:

The Leer 100R camper shell does not have lock cylinders that are directly compatible with anything we currently offer. The Bolt Lock # BL7023482 you referenced are for tool boxes and the product dimensions are 2 x 1.5 x 1.5 inches.

expert reply by: Jason S

0

Answer 1

I believe you are referring to something like the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers #PAL9555 which adds a power lock to the ARE camper shell on your 2016 Ford F-250. The only other thing that you might be…

view full answer...

Answer 2

The Replacement Lock Cylinder for BOLT Toolbox Latch - Codes to Toyota Key #BL7023482 are designed for truck tool boxes, so I can't guarantee a fit on your Snugtop Pro Camper. The cylinder is a fit for the standard 3/4 inch hole of toolboxes and…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Replacement Lock Cylinder Compatibility with Leer Camper Shell

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching