Recommended Rear Anti-Sway Bar for 2007 Chevy Express Class C Chassis

Question

Question:

I have a 2007 chevy express class C built in 12/06. I do have the shock mounts with the holes in the rear. Going by the build dates I should need the axle mount kit but it looks like all the kit does is supply a mount base which it looks like I already have. Is the mounting base the only reason for the kit?

asked by: Ian M

0

Expert Reply:

I checked with Roadmaster and did verify that the Roadmaster Rear Anti-Sway Bar # RM-1109-175-00 is confirmed to fit your 2007 Chevy Express Class C chassis. The axle mounting kit (which is included with this part number) is indeed to allow for an attachment point and base on the axle. My contact did say that if the chassis was built before 6/2006 the kit should be needed.

Take a look at the installation video I attached so you can see exactly how the bracket kit is used. If you can send me a picture of your existing setup, I will also be happy to verify with Roadmaster if the mounting kit is needed for your specific application.

expert reply by: Chris R

0

Answer 1

The fit of a Sway Bar like Roadmaster RM-1109-175 depends on the specific version of your base Chevy Express Van. For instance, if you have the 2500/3500 Class C Cutaway you can use part #RM-1109-175. This also fits other versions such as the…

view full answer...

Answer 2

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 3

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 4

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Recommended Rear Anti-Sway Bar for 2007 Chevy Express Class C Chassis

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching