Atwood Landing Gear Replacement for 36 Long Landing Gear
Question:
I require a lead leg for my 5th wheel. It’s an Atwood product and I understand that Lippert has bought them out. The leg is 36” long and 2 1/2” diameter. I’m unable to find one
asked by: Rick
Helpful Expert Reply:
To replace the Atwood landing gear on your 5th wheel trailer you will need to measure the distance between your weld stops. This is typically 15-1/2" on the inside and 17-1/2" on the outside (see attached photo). We do have replacement options but since Atwood is no longer in the landing gear business you need to replace your whole landing gear set to ensure that the gear ratio and strengths are the same.
If your weld stop locations match the picture then I recommend using the 8,000 lb Landing Gear Set # RVLG-8000. These feature a retracted height of 32-3/4" and an extended height of 53-1/4". For a manual crank use part # RVLG-HDL but if you would like to add a motor use part # LC142178.
Products Referenced in This Question
Lippert Venture 5th Wheel RV Landing Gear Motor
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Motor and Gear Parts
- Motor
- Lippert
more information >
Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Handles and Cranks
- Sidewind
- etrailer
more information >
Product Page this Question was Asked From
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Landing Gear Set - 36-1/2" Lift - 8,000 lbs
- Shop: Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Shop: Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Shop: Replacement Lead Leg for Venture 5th Wheel RV Landing Gear
- Shop: Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 6,500 lbs
- Shop: Replacement Lead Leg for Keystone Montana 5th Wheel Landing Gear
- Q&A: How to Choose the Correct Replacement Landing Gear for 5th Wheel Trailer
- Shop: Replacement Gear Kit for etrailer and Ram Round Swivel Marine Jacks - 1,200 lbs and 1,500 lbs
- Q&A: Replacement Bulldog Landing Gear Recommendation for Prowler 5th Wheel
- Video: etrailer Landing Gear Set Review
- Search Results: atwood landing gear
- Video: etrailer Camper Jack - Landing Gear - RVLG-8000 Review
- Shop: RV Jack Pads
- Shop: RV Antenna and Radio
- Search Results: tuff tow
- Q&A: Are Replacement Parts for Atwood Landing Gear Available or Will Another Brand Fit
- Q&A: Installation Instructions for Bulldog Powered-Drive Kit # BD1824200100
- Q&A: Amp Draw and RPMs of Replacement Gear Motor Assembly for Lippert Electric Slide-Out 386322
- Search Results: landing gear
- Video: etrailer and Ram Swivel Marine Jacks Rebuild
- Q&A: Replacement Motor and Gearbox for Atwood 75721
- Q&A: Replacement Electric Motor for the Atwood Motor # 75722
- Search Results: rvlg~8hdl
- Search Results: replacement landing gear leg
- Search Results: slide out motor
- Search Results: atwood landing gear leg