2 Inch Ball Mounts with 4 Inch Drop Compatible with Reese Sway-Control Bracket
Question:
I received this part and immediately discovered my drawtite 4281 ballmount is too wide 3 for it to fit. How do I determine the width of any given ballmount that you sell? That specification does seem to appear on the ballmount description. I need a 4inch drop 7,500 or more GTW ball mount with 1inch shank hole for 2inch receiver. Can you list every ball mount that meets that description?
asked by: Alan W
Helpful Expert Reply:
As you mentioned in your question, the Reese Sway-Control Bracket # RP26003 requires the ball mount platform it is used with to be narrower than 2-5/8 inches.
I narrowed down our available selection of ball mounts to those that meet your requirements (2 inch hitch, 4 inch drop, 1 inch ball hole, 7,500+ pound capacity) and then went out to our warehouse to measure the ball platform widths on these units. I found that the following ball mounts match what you are needing and feature a ball platform narrower than 2-5/8 inches for use with your Sway-Control Bracket.
Convert-A-Ball Ball Mount # AMSC4
Draw-Tite Ball Mount # 2753
Curt Ball Mount # C45230
I have also attached a video demonstration for each of these ball mounts that you can check out.
Products Referenced in This Question
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Draw-Tite
more information >
Convert-A-Ball Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 10,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Shock Absorbing
- Convert-A-Ball
more information >
Curt Dual Length Ball Mount for 2" Hitches - 2-3/8" Rise, 3-5/8" Drop - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Product Page this Question was Asked From
Reese Sway-Control Bracket for 2" Ball Mounts - Class III and IV
- Accessories and Parts
- Weight Distribution Hitch
- Adapters
- Sway Control Parts
- Brackets
- Reese
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Recommended Trimax Trailer Wheel Chock and Lock for 175/80R/13 Tires
- Article: How to Measure for Trailer Hitch Drop
- Article: Which Sway Control Hitch is Right For Your Trailer?
- Q&A: Parts Needed to Add Brake Controller to 2024 Toyota Sienna Platinum
- Article: RV Roof Types: What Type of Roof Does My RV Have?
- Q&A: Can Sway Control be Used on a Trailer without Using Weight Distribution
- Q&A: Can The Furrion Vision S Prewired System Be Switched to Us Voyager WiSight Camera System?
- Q&A: Recommended Sway Control for 1800 lbs 13 Foot Scamp Travel Trailer
- Article: Steel vs. Aluminum Ball Mounts
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Q&A: Replacement Motor For A Thompson Saginaw Part No. 7831293
- Q&A: How to Determine if a Vehicle has a Class I or Class II Trailer Hitch
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: 30-Amp and 50-Amp RV Service: What's the Difference?