Can Cotter Pin Be Used to Secure Yates Ribbed Wobble Roller YR343R-6P

Question

Question:

Can I use a stainless cotter pin instead of a retaining rings?

asked by: Dan

0

Expert Reply:

If the 3/4-inch shaft where you intend to install Yates Ribbed Wobble Roller # YR343R-6P has a hole for a cotter pin, then yes, you can secure the wheel that way and I suggest placing a flat washer between the roller and the cotter pin to avoid any potential for abrasion.

expert reply by: Adam R

0

Answer 1

Basically, you put the open end around the shaft on each end of the roller then use some pliers to clamp it closed so it is tight to the shaft. This allows the roller to roll but stay in position. I made a video showing what this would look like for…

view full answer...

Answer 2

The diameter of the retainer ring #CE10981 is 3/16 inches. Yes, you could use it on a 1 inch shaft as well.

view full answer...

Answer 3

The way to install the new #YR343R-6P roller is pretty simple. You'd can use pliers or channel locks to remove the existing retainer ring and the old washer. Then remove the old roller. install the new roller part #YR343R-6P and washer part…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Can Cotter Pin Be Used to Secure Yates Ribbed Wobble Roller YR343R-6P

Product Page this Question was Asked From

Continue Researching