Recommended Clearance Light For Enclosed Trailer Fenders
Question:
Hello. I have a brand new Freedom closed trailer. The wheel wells have LEDamber/red running lights.Im looking for a set of light that will replace the running lights but also act as a turn signal light.
asked by: David M
Expert Reply:
We have the following options that are intended to be clearance lights but could be wired to be used as turn signals:
LED Clearance Light Assembly for Trailer Fender - Trailers over 80" Wide - Driver Side # MCL12ARLB and passenger side # MCL12ARRB.
Left Fender Clearance Trailer Light, Prewired - Amber and Red # BA44FNL and right # BA44FNR.
LED Trailer Fender Clearance Light - Submersible - 2 Diodes - Amber/Red - Driver or Passenger Side # MCL180ARB.
You can wire these for turn signals but you will need to use a 2-to-3 converter to isolate signals.
Products Referenced in This Question
Incandescent Trailer Fender Light w/ Reflector - 2 Bulbs - Red and Amber Lens - Driver Side
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Rectangle
- Surface Mount
- Submersible Lights
- Incandescent Light
- 8-1/2L x 3-1/4W Inch
- Red and Amber
- Optronics
more information >
Incandescent Trailer Fender Light w/ Reflector - 2 Bulbs - Red and Amber Lens - Passenger Side
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Rectangle
- Surface Mount
- Submersible Lights
- Incandescent Light
- 8-1/2L x 3-1/4W Inch
- Red and Amber
- Optronics
more information >
Curt 2 to 3 Wire Tail Light Converter
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal
- CURT
more information >
LED Clearance Light Assembly for Trailer Fender - Trailers over 80" Wide - Driver Side
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Surface Mount
- Submersible Lights
- LED Light
- 4-3/4L x 1-5/8W Inch
- Red and Amber
- Optronics
more information >
LED Trailer Fender Clearance Light - Submersible - 2 Diodes - Amber/Red - Driver or Passenger Side
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Rectangle
- Surface Mount
- Submersible Lights
- LED Light
- 8-1/2L x 1-11/16W Inch
- Red and Amber
- Optronics
more information >
Product Page this Question was Asked From
LED Clearance Light Assembly for Trailer Fender - Trailers over 80" Wide - Passenger Side
- Trailer Lights
- Clearance Lights
- Rear Clearance
- Side Marker
- Round
- Surface Mount
- Submersible Lights
- LED Light
- 4-3/4L x 1-5/8W Inch
- Red and Amber
- Optronics
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Tire TLC: How & When to Check Your RV/Trailer Tire Pressure
- Q&A: Replacement Cable and Pin for Bright Way Breakaway Switch on Trailer 2348
- Q&A: Torsion Spring for Trailer Ramp Door that Weighs 200 lb
- Q&A: Where is the Factory Trailer Brake Controller Port On a 2022 Chevrolet Tahoe
- Q&A: Wiring 3-Wire Breakaway Switch as Replacement for 2-Wire Switch
- Q&A: Installing Brake Controller On 2009 Ford E-350 Van
- Article: Brake Controller Installation on a Ford Full-Size Van
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Height Dimensions Of The Z-Rail for Enclosed Trailer # 362417-955
- Article: Trailer Wiring Diagrams
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Q&A: Which Trailer Brake Magnets Do I Need to Use
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Article: How to Measure Your Trailer Wheel Bolt Pattern