Recommended Towing Components for 2012 Infiniti G37X
Question:
Hello, I am going to use the hitch for towing, I have a 2012 G37X. Im planning on getting a jet sky soon and wanted to do some research before getting into a hitch that will not be strong enough.
asked by: Gerson B
Expert Reply:
For your 2012 Infiniti G37X, the Curt Trailer Hitch Receiver - Class I # C11499 is a confirmed fit. Then you can use the ball mount # C45521 and pin # F-4. You can then use hitch ball # A-80 for a 1-7/8 inch hitch ball or # A-82 for a 2 inch ball.
For your trailer wiring, I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56033. This will install to the harness located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area. Then you will run the power wire directly to the vehicle battery. I've attached an article to help with routing that wire.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt Hitch Pin and Clip for 1-1/4" Hitches - 1/2" Diameter x 2-1/2" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- 2-1/2 Inch Long
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- 2-1/2 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: 2012-2013 Infiniti G37 Sedan Hitch and Bike Rack Recommendation
- Q&A: Aluminum Fascia Support on 2009 Infiniti G37 is Welded On and Cant Install Trailer Hitch
- Q&A: Hitch Recommendation for a Infinity G37X
- Q&A: Does Bumper Fascia Spacer Need to Be Reinstalled on 2013 Infiniti G37 When Installing Curt Hitch
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Are Longer Bolts Needed When Installing Curt on 2012 Infiniti G25
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How to Pick Out Bearing for 10,000 lb Dexter Axle
- Q&A: What is the Difference Between Class 1 and Class 2 Hitches for the Scion XB
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: Best Bike Racks for Fat Bikes
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Hitch Receiver Sizes
- Article: Best Bike Racks for Electric Bikes