Video Showing How to Make Initial Adjustments on Self-Adjusting Electric Trailer Brakes

Question

Question:

Do you have a how to video describing the initial adjustment on the AKEBRK-35-SA?

asked by: Alan F

0

Expert Reply:

I have linked a couple of videos. One is just the review of brake set # AKEBRK-35-SA. The other is a video explaining the initial set up of self-adjusting brakes which will be nearly identical with brake set # AKEBRK-35-SA.

expert reply by: Michael H

0

Answer 1

The studs on the Dexter 7 inc brake assembly, part #23-47, are 1-1/4 inch long with 7/16 - 20 threads. Brake Assembly mounting bolt, part #7-75, is 1-1/4 inch long with 7/16 - 20 threads. The nuts, part #6-17, are also 7/16 - 20. This size is pretty…

view full answer...

Answer 2

I went ahead and called my contact at Redline Trailer Repair Parts, and they confirmed that nuts in the Mounting Hardware for 10" Brake Assemblies #BRKH10B have a diameter of 7/16mm and have 20 threads per inch. Unfortunately, there are no bolts…

view full answer...

Answer 3

Did your 2018 GMC Yukon XL come with a factory trailer connector? If not then the port is not present and the brake controller would need to be hardwired into the vehicle's wiring harness. If it did then the port should be located up under the…

view full answer...

Answer 4

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Video Showing How to Make Initial Adjustments on Self-Adjusting Electric Trailer Brakes

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching